For Ford Powerstroke 6.0L&7.3L Fuel &Oil Pressure Mechanical Gauge Test Tool Kit

Description

Description:
100% brand new, Never been tried or installed
The tool is primarily designed to test fuel pressure while driving.
The tool can test fuel or low side oil pressure.
The set is essential to see the pressure drop with a load on the engine.
It comes with all the fittings needed for both 6.0 & 7.3 engines.
No instructions included
Professional installation is highly recommended
Package including:
Assembled pressure test hose and gauge set
Needed fittings/adapters
As shown in the Picture Show
Materials:
AUTO PARTS
For Ford Powerstroke 6.0L&7.3L Fuel &Oil Pressure Mechanical Gauge Test Tool Kit
Description:
100% brand new, Never been tried or installed
The tool is primarily designed to test fuel pressure while driving.
The tool can test fuel or low side oil pressure.
The set is essential to see the pressure drop with a load on the engine.
It comes with all the fittings needed for both 6.0 & 7.3 engines.
No instructions included
Professional installation is highly recommended
Package including:
Assembled pressure test hose and gauge set
Needed fittings/adapters
As shown in the Picture Show
Materials:
100 psi liquid filled gauge- (High quality stainless steel body with shatter-resistant rubber casing)
300 PSI rated fuel & oil hose
Lever action suction cup for securing the gauge and easier reading;
Needed JIC fittings/adapters.
Application Details:
To test Fuel pressure on a 6.0, use an allen wrench removing the plug located at the bottom front of the fuel filter housing and then install the 1/4" jic x M12-1.5 adapter.
To test oil pressure on a 6.0, please remove the "single wire", oil pressure sensor, and utilize that port with the 1/4" jic x #4 orb adapter. (Sensor is located on top of the oil cooler housing in front of the turbo)
For 7.3 fuel pressure test, there's 2 plugs on the back of the fuel filter housing. Upper driver side is the pre-filter port. Lower passenger side is the post filter port. (Most people use the pre-filter port because its easier to reach) Then you would install the 1/4" jic x #4 orb adapter.
For 7.3 oil pressure test, you have 2 options. You can remove the "single wire", oil pressure sensor located on top front of engine, and then install the 1/4" jic x #4 orb adapter. Or, you can remove 1/8" npt plug located at the oil filter head and then install the 1/4" jic x 1/8" npt adapter.
This tool may probably work on many other engines, including gas engines. If the engine has a 7/16-20 thread test port at the fuel rail, just remove the shrader valve before connecting the tool.
Notes:
After any fuel pressure test, you may leave the adapter installed and cap it with the provided JIC cap. The JIC plug is used to block off the end of the tool for storage.
Any questions please contact us via eBay and we'd love to help you out.
Item Specifics
Brand
Unbranded
Manufacturer Part Number
Does Not Apply
Vehicle Type
Heavy Duty/Commercial, Passenger Vehicle
Accessories
Fittings, Hoses
Maximum PSI
100 PSI
Engine Type
Diesel
Features
Dual Scale Range, Gauge Hook
Warranty
Yes
UPC
Does not apply
PAYMENT
We accept PayPal payment and other payments through PayPal.
Payment
We accept PayPal payment and other payments through PayPal.
SHIPPING
Notice: The Guaranteed Date is automatically generated and displayed by ebay. We can't change it and can't control the speed of delivery, it's depend on the carrier. We will ship your item out asap after the payment is clear.
Usually your Items will be shipped within 1-3 business day after your payment is cleared.
International orders may take 10 to 30 business days to arrive.
We have CA, NJ and GA
warehouses and ship items may vary according to the stock.
Friday orders will be shipped next Monday morning.
For the PR,HI,GU and AK,we have add the shipping fee for the some items that needs.
For the
Saipan,Virgin Islands and Guam,some items may need add shipping fee,we will note to you asap to see whether you'd like accept.
RETURN
You can return your unused items back for exchange or refund within 30 days.
Please contact us for return process before you return the item.
CUSTOMER SERVICES
Usually your message will be answered within 1 business day.
Your message over the weekend will be answered on Monday,and holiday messages will be answered once we get to work.
AUTO PARTS
WELCOME TO FIRST.RACING
Shop Category
Store Home
Exhaust Systems
◈  Exhaust Manifolds & Headers
◈  Exhaust Pipes & Tips
◈  Mufflers
◈  V Clamps
◈  Turbo Chargers & Parts
◈  Exhaust Wraps
◈  Exhaust Cutout
Intake Systems
◈  Air Intake Systems
Timing Components
◈  Timing Chain Kit
◈  Timing Belt Water Pump Kit
◈  Control Solenoid Valve
Suspension & Steering
◈  Shocks & Struts
◈  Coil Springs
◈  Lift Kits & Parts
◈  Power Steering Pumps & Parts
Chassis Parts
◈  Control Arms & Parts-OEM
◈  Control Arms
◈  Sway Bars
◈  Caster/Camber Kits
Engines & Components
◈  Motor Mounts
Cooling Systems
◈  Fans & Kits
◈  Radiators & Parts
◈  Intercooler Piping Kit
◈  Hoses & Clamps
Exterior
◈  Hoods
◈  Mouldings & Trim
◈  Tailgates & Liftgates
Brakes & Brake Parts
◈  Air Dryers
◈  Master Cylinders & Parts
Interior
◈  Dash Parts
◈  Locks & Hardware
Automotive Repair Kits
◈  Other Automotive Tools& Supply
◈  Diagnostic Service Tools
Parts & Accessories
◈  Go Kart Parts
Gaskets
◈  Cyl. Head & Valve Cover Gasket
Hangers, Clamps & Flanges
◈  T Clamps
◈  Narrow Clamps
◈  Step Clamps
◈  Butt Joint Clamp
◈  Hoses & Clamps
Transmission & Drivetrain
◈  Universal Joints & Driveshafts
◈  Transmission & Drivetrain
Air Intake & Fuel Delivery
◈  Fuel Inject. Controls & Parts
Fuel Oil Line & Fitting
◈  Fuel Oil Line
◈  Fuel Oil Fitting
◈  Other Fittings & Adapters
Other
Hot Item
16"ELECTRIC RADIATOR FAN HIGH 3000 CFM THERMOSTAT WIRING SWITCH RELAY KIT BLACK
USD 40.99
2x 12" Universal Slim Fan Push Pull Electric Radiator Cooling 12V Mount Kit BK
USD 33.99
4X 2.5" Stainless Steel T-Bolt Clamps Turbo Intake Silicone Hose Coulper Clamps
USD 8.99
7" inch Universal Slim Fan Push Pull Electric Radiator Cooling 12V Mount Kit
USD 18.88
Silicone Hose T-Bolt Clamp 301 Stainless Steel Clamps Choose Your Size 51 63 76
USD 2.09
New Item
K159 5PCS ENGINE MOTOR & TRANS MOUNT SET MANUAL FIT 1998-2001 HONDA CRV 2.0L
USD 52.25
Radiator AC A/C Condenser Cooling Fan Fit 2011-18 Ford Fiesta 1.0 1.6L FO3115186
USD 39.89
3" Vband Cast Stainless Steel 90 Degree Elbow Adapter Flange For T4 Turbo
USD 41.99
Full Shocks Struts Absorber Set For 2004-2009 Mazda 3 & 2006-2010 Mazda 5
USD 84.55
3-Row Full Aluminum Racing Cooling Radiator For 67-69 Chevy Camaro/Firebird T/A
USD 103.55
For Ford Powerstroke 6.0L&7.3L Fuel &Oil Pressure Mechanical Gauge Test Tool Kit
Description:
100% brand new, Never been tried or installed
The tool is primarily designed to test fuel pressure while driving.
The tool can test fuel or low side oil pressure.
The set is essential to see the pressure drop with a load on the engine.
It comes with all the fittings needed for both 6.0 & 7.3 engines.
No instructions included
Professional installation is highly recommended
Package including:
Assembled pressure test hose and gauge set
Needed fittings/adapters
As shown in the Picture Show
Materials:
100 psi liquid filled gauge- (High quality stainless steel body with shatter-resistant rubber casing)
300 PSI rated fuel & oil hose
Lever action suction cup for securing the gauge and easier reading;
Needed JIC fittings/adapters.
Application Details:
To test Fuel pressure on a 6.0, use an allen wrench removing the plug located at the bottom front of the fuel filter housing and then install the 1/4" jic x M12-1.5 adapter.
To test oil pressure on a 6.0, please remove the "single wire", oil pressure sensor, and utilize that port with the 1/4" jic x #4 orb adapter. (Sensor is located on top of the oil cooler housing in front of the turbo)
For 7.3 fuel pressure test, there's 2 plugs on the back of the fuel filter housing. Upper driver side is the pre-filter port. Lower passenger side is the post filter port. (Most people use the pre-filter port because its easier to reach) Then you would install the 1/4" jic x #4 orb adapter.
For 7.3 oil pressure test, you have 2 options. You can remove the "single wire", oil pressure sensor located on top front of engine, and then install the 1/4" jic x #4 orb adapter. Or, you can remove 1/8" npt plug located at the oil filter head and then install the 1/4" jic x 1/8" npt adapter.
This tool may probably work on many other engines, including gas engines. If the engine has a 7/16-20 thread test port at the fuel rail, just remove the shrader valve before connecting the tool.
Notes:
After any fuel pressure test, you may leave the adapter installed and cap it with the provided JIC cap. The JIC plug is used to block off the end of the tool for storage.
Any questions please contact us via eBay and we'd love to help you out.
PAYMENT
We accept PayPal payment and other payments through PayPal.
Payment
We accept PayPal payment and other payments through PayPal.
SHIPPING
Notice: The Guaranteed Date is automatically generated and displayed by ebay. We can't change it and can't control the speed of delivery, it's depend on the carrier. We will ship your item out asap after the payment is clear.
Usually your Items will be shipped within 1-3 business day after your payment is cleared.
International orders may take 10 to 30 business days to arrive.
We have CA, NJ and GA
warehouses and ship items may vary according to the stock.
Friday orders will be shipped next Monday morning.
For the PR,HI,GU and AK,we have add the shipping fee for the some items that needs.
For the
Saipan,Virgin Islands and Guam,some items may need add shipping fee,we will note to you asap to see whether you'd like accept.
RETURN
You can return your unused items back for exchange or refund within 30 days.
Please contact us for return process before you return the item.
CUSTOMER SERVICES
Usually your message will be answered within 1 business day.
Your message over the weekend will be answered on Monday,and holiday messages will be answered once we get to work.